If you go to the website VanderbiltCupRaces.com that is run and was created by my good friend Howard Kroplick you will see Locomobiles that were in the Vanderbilt Cup Races here on long island in period photos. many that I contributed. I used to be on a committee of the Long Island Old Car Club that would host a event to commemorate the assorted Vanderbilt Cup Races decades ago with Austin Clark on the same committee. At the 1988 event when the 1908 race was a century old , Jerry Helck brought Old 16 over from his home in N.J. and drove the car in the event. We had 100 cars participate in a driving tour and the newest was made in 1938.
I am registered follower of Howards Vanderbiltcupraces for some time now. I enjoy the effort put into that website! Howard does a fine job. Original Locomobile Racecars, that still exist, are certainly a huge rarity. That said, I know of several Locomobile Automobiles that have been put back into service as speedsters, racecars or specials. This chat area is the place for owners of original Locomobile Racecars or modern creations that put another Locomobile back on the road as a Racecar, Speedster or Special to converse and share information or stories. Walt, thanks for your response.
Al
Walt, Do you have any photos from the drive you referred to from 1988. Those images and adjoining stories would be a nice addition to this chat. (I wish I had been there)!
Al
Who has pictures of early or current built speedsters/specials based on Locomobile. In the past, I have seen several random Locomobile speedsters but don't have pictures of them to post here.
Al
Here is a vintage picture of what looks to be an early 1910-11 Locomobile model L factory Baby Tonneau, (not necessarily a home built speedster or racecar but is a factory built speedster). It lloks like the young spirited lady is finishing a cut of melon before she heads into the sunset with her Locomobile. Is that a Baby Grand Chevrolet in the background?
Al

OK Al,
Been working on drivetrain dimensions, laying out radiator, engine, transmission, steering column, simulated plywood firewall, hood, steering column, and dash panel with an old seat I picked up.
If I remove the hinge pillars from the back of these seats they may have a decent line to work with.
rydersclassicsJun 16, 2023OK Al,
Been working on drivetrain dimensions, laying out radiator, engine, transmission, steering column, simulated plywood firewall, hood, steering column, and dash panel with an old seat I picked up.
If I remove the hinge pillars from the back of these seats they may have a decent line to work with.
Here are some pictures of what I have been doing.Took 10" out of the rear frame horns and 14" out of the frame rails. I should end up with a 128+-" wheel base.
sorry, I can't see or open these pictures.
Hello Steve, Did you set back the radiator, as was typical of early racecars? You are saving extra bits and pieces of Locomobile, good for you.
Al
Hello Al,
Yes the early racers typically set the radiators back. I haven't found any examples of Locomobile racers as late as 1914 or 1915 so if you are aware of any I would love to see some pictures for reference.
On the other hand there are examples of Speedsters. Cut Downs, Gow Jobs, Specials, Jalopies, Hot Rods.....
Not sure what label fits my project yet or if it will have fenders, at this point I am looking for that balance between form and function using as much as possible from this pile.
To your point, on this particular chassis the radiator support was back 1.75" from the factory compared to the other 3 I have, don't known why.
As we do know Locomobile would build anything the customer wanted.
So I stand in my old drafty barn day dreaming of that wealthy son in 1915, working with DeCausse of course, try to finding the right balance between the steering column angle, seat height/position that fits me on this 128 inch wheelbase chassis.
More likely the poor Locomobile factory minion collecting up floor sweeping then dragging them back to some shed and risking everything if found out, to coble together a Locomobile Jalopy Racer of his own.
Either way "living the dream".
You are describing what motivates each of us in this old car hobby, maybe just a different approach or angle. I will make a few contacts and see if they will respond here with you on this subject of speedsters specials or racecars. One thought on "racecar" design. I would think that the form and function of a 1915ish race car would not necessarily be true to one make alone. I certainly like and appreciate the design used by Stutz during those very years. Locomobile is so very similar. When will you be addressing your engine rebuild?
Al
Yes sir,
From the bottom up Al. I have the makings of 2 decent engine builds. Initial inspection of cams, rods, crank shafts, valves, pistons, and cylinders all show very little wear, likely very low miles.
My confidence is high that the engine will come together, now the engine is a lower priority than making best use of the summer weather.
At this point my primary focus is to build the rolling chassis, determine final locate of all drive train components and body.
Both axles and transmission are ready to go. The crankcase is set back about 3.5" compared to the 1920 48 I have and on this 128" wheelbase the weight distribution should be much better.
With the long, set back six cylinder engine there are engineering challenges to overcome.
More on that later.
For now I am fixated on creating my body design.
Like you I find 1915 Stutz's, (and Mercer's) to be as good as it gets. This build will be the closest I will ever get to those timeless super stars.
There is another consideration worth mentioning. I am 6' feet tall, 250lb. and 68 years old, and I intend to drive this thing, so I am thankful for the large size of Locomobile.
Everything was changing in 1915. so you can't go to wrong if your happy with the results, but ! ? . . .
Are you envisioning a body rather similar to the last picture you posted of a Stutz? Your proportions are certainly similar to that car. Does anyone reading here know what CID is for a 6 cylinder 1915-17 Wisconsin powered Stutz would be?
Al
I love both styles and the European flair of the hood leans towards this Mercer picture but as mentioned I intend to drive it so the sides need to be much lower.
Tomorrow I will be building a mock up tank 2 inches smaller in diameter for a visual and time permitting using ram board to simulate body panel lines.
Am enjoying my fathers day today and looking forward to tomorrow's adventure.
More to follow!
Happy fathers day to all!
Are you thinking of step over sides like the Mercer or step thru like a Stutz Bearcat?
Al
If you look at the last pictures posted the last one has seats with high arm rests like the Stutz.
The first 2 pictures show seats without integral armrests that could be styled like the Mercer so I am experimenting with both styles .
If you refer to the Cooper at Indy Stutz race car, it has a side panel line like the Mercer but much lower, this is the direction I am heading at present, so a blend.
Either way I need to keep the step over panel lower than the pictured Mercer for egress.
.
Many ways to skin that cat. Less is more.



To join in the conversation, you must be a club member.
You’re welcome to read and like every post. Members can reply and start topics of their own.











.png.040447bf6fc4ba3624f5e74997ad64f7.webp)
.png.bc878de770eb8771c112e7c2f25d2999.webp)






